VOXELASE
All free tools

Laser Engraving Price Calculator: What to Charge per Piece

By Es Seddyk Naaoui4 min read

To price a laser engraving job, add the material, machine time and your own labour for the whole order, divide by one minus your target margin and any marketplace fee, then divide by the quantity. The calculator below does that arithmetic and shows what the order pays you per hour.

It is currency-neutral and runs in your browser. Nothing you type is stored or sent anywhere.

Laser Engraving Price Calculator

Enter what one order really costs you in material, machine time and your own time. The calculator returns the price per piece that still leaves your target margin after fees.

Price per piece13.78
Order total137.75
Profit on the order55.10
Cost per piece8.27
Laser time1.1 h
Earned per hour of your time85.10
Materials & packaging
44.25
Machine time
8.40
Your labour
30.00
Fees
0.00
Currency-neutral: use dollars, euros or pounds, as long as every field uses the same one. Tax is not included.

What each field means

  • Blank / material cost per piece: what one tumbler, board, coaster or sheet section costs you delivered, including shipping to your door.
  • Packaging and consumables: box, tissue, masking tape, cleaning supplies, marking spray.
  • Laser run time per piece: the job time your software reports. The laser can run unattended, so this is charged at the machine rate, not at your labour rate.
  • Hands-on time per piece: loading, aligning, masking, cleaning, finishing and packing.
  • Design and setup for the order: customer messages, artwork, the proof, the test piece and the jig. This is charged once and spread across the quantity.
  • Machine cost per hour: what an hour of laser time costs you to own and run.
  • Spoilage: the share of pieces you expect to remake.
  • Target profit margin: the share of the selling price left after every cost, including paying yourself.
  • Marketplace and payment fees: the percentage taken by the platform and the card processor.

How much should you charge for laser engraving?

Charge the full cost of the order divided by one minus your margin and fee percentages. Written out:

price = (materials + machine time + labour) ÷ (1 − margin − fees)

Take the calculator's default order as a worked example: ten pieces, a blank that costs 3.50, packaging at 0.75, six minutes of laser time and three minutes of handling each, thirty minutes of setup, labour at 30 an hour, a machine rate of 8 an hour, 5% spoilage and a 40% margin with no fees. Materials come to 44.25, machine time to 8.40 and labour to 30.00, a cost of 82.65. Dividing by 0.6 gives an order price of 137.75, or about 13.78 per piece.

That number is a floor based on your costs. If comparable work sells for more in your market, charge more. If it sells for less, the calculator has just told you which jobs to decline.

Is margin the same as markup?

No, and mixing them up underprices every job. Markup is added to cost: a 40% markup on a cost of 100 gives a price of 140, which is a margin of only 28.6%. Margin is measured against the selling price: a 40% margin on a cost of 100 needs a price of 166.67. This calculator works in margin, because fees and profit are both taken out of what the customer pays.

Fees behave the same way. A 10% marketplace fee is charged on the selling price, so adding 10% to your cost does not cover it. The fee has to be solved for inside the price, which is what the formula above does.

How do you work out the machine cost per hour?

Divide what the machine costs you over its life by the hours you expect to run it, then add power and consumables.

machine rate = (purchase price ÷ expected working hours) + electricity per hour + maintenance per hour

For example, a machine bought for 2,400 that you expect to run for 1,500 hours before replacing it costs 1.60 per hour in depreciation. Add your electricity for the laser, extraction and chiller, and an allowance for lenses, CO₂ tubes or diode modules, filters and honeycomb. Use your own figures; a rate that only covers electricity means the business never saves enough to replace the laser.

Why does the price per piece drop with quantity?

Because setup is a fixed cost. Thirty minutes of design and proofing costs the same for one piece as for fifty. On a single custom item the setup can be most of the price; on a batch it nearly disappears. Change the quantity in the calculator to build a price-break table for a quote, and consider a minimum order charge for one-offs.

What the calculator leaves out

Sales tax and VAT are not included, because the rules depend on where you and the customer are. Shipping charged to the customer is also left out. Rent, insurance, software and marketing are overheads: either fold them into the machine rate or the labour rate, or check that your margin is large enough to carry them.

For what to make, the laser engraving ideas guide groups projects by material and machine. Material guides with starting settings cover cutting boards, leather, acrylic and metal. More calculators are in the free toolbox.

Build machine-ready depth maps offline

DepthGen Pro exports 8-bit and 16-bit PNG, EXR, STL and OBJ for laser, CNC and 3D-print workflows.

See pricing

Related reading