VOXELASE
All free tools

Free Living Hinge Generator: Laser-Cut Flex Patterns as SVG and DXF

By Es Seddyk Naaoui3 min read

This free generator draws a living hinge pattern to your exact dimensions and exports it as an SVG or DXF in millimetres. Enter the hinge width and height, choose straight, wave or oval cuts, set the slit length, bridge and column spacing, and download a file your laser software opens at true size.

A living hinge (also called a lattice hinge or kerf bend) is a field of staggered cuts that lets a flat, rigid sheet of plywood, MDF or acrylic bend into a curve.

Living Hinge Generator

Set the panel size and the slit geometry, preview the lattice, then download a laser-ready SVG or DXF in millimetres.

Cuts84
Fitted slit length29.3 mm
Total cut length2.11 m
Slits are red and the outline is blue, so they land on separate layers in LightBurn and xTool software. Cut the slits first, then the outline.

How to use the generator

  1. Hinge width is the length of the flexible zone, measured around the bend. Hinge height is the length of the bend axis. The slits run along the height, and the sheet bends around them.
  2. Slit length sets how long each cut is. The tool adjusts it slightly so a whole number of slits fits the height, and shows the fitted value.
  3. Bridge is the solid material left between the end of one slit and the start of the next.
  4. Column spacing is the distance between neighbouring rows of slits.
  5. Download the SVG or DXF and place it into your own design, or cut it as a test strip first.

How does a living hinge work?

The staggered slits turn the sheet into a chain of thin strips that twist. Wood and acrylic do not stretch enough to bend tightly, but a narrow strip can twist a few degrees along its length without breaking. Each column of slits is offset by half a period from the next, so every strip between two columns is held only at its ends. When you bend the panel, each strip twists a little, and the small twists add up to a large curve.

That is why three numbers control the result: longer slits and closer columns make longer, thinner strips that twist further, and a narrower bridge makes the joints between them weaker.

Which settings make the hinge more flexible?

ChangeEffect on flexibilityCost
Longer slitsMore flexibleWeaker panel, more sag
Smaller column spacingMore flexible, tighter radiusMore cutting time, more charring, fragile strips
Narrower bridgesMore flexibleBridges crack first when overbent
Wider hinge zoneSame stiffness, larger total bend angleUses more of the part
Thinner sheetMuch more flexibleLess rigid part overall

A reasonable first test in 3 mm birch plywood or MDF is the default: 30 mm slits, 4 mm bridges and 2.5 mm column spacing. Cut a 60 × 100 mm strip, bend it by hand, and adjust one value at a time. Material batches vary enough that a test strip is faster than calculating.

Which pattern should you choose?

Straight slits are the strongest and fastest to cut, and they bend in one direction only. Wave slits spread the stress along a curve, which helps brittle material and looks decorative. Oval cut-outs remove a sliver of material at every slit, so neighbouring strips do not rub and the hinge bends further before binding, at the cost of a weaker panel.

What materials work for a living hinge?

Thin, uniform sheet works best: 3 mm birch plywood, MDF, basswood and cardboard. With plywood, run the slits parallel to the face grain so the strips are not short-grained. Cast acrylic can be hinged, but it is brittle, so use longer slits, wider spacing and a gentle radius. Solid hardwood tends to split along the grain.

Remember the kerf. A laser removes roughly 0.1 to 0.2 mm of material per cut, so every slit is slightly wider than a line and every strip slightly thinner than the spacing suggests. On very tight spacing that difference is a large share of the strip.

How do you import the file?

Import the SVG or DXF without scaling. Both files are in millimetres. The slits are drawn in red and the panel outline in blue, so LightBurn and xTool software put them on separate layers. Cut the slits first and the outline last, so the panel does not shift while the lattice is still being cut. If you are new to layers and cut order, the LightBurn tutorial walks through them.

More free maker tools

The jigsaw puzzle generator produces laser-cut puzzle SVGs in the same way, and the free laser cut files directory lists libraries of ready-made designs. Every Voxelase tool is in the free toolbox.

Build machine-ready depth maps offline

DepthGen Pro exports 8-bit and 16-bit PNG, EXR, STL and OBJ for laser, CNC and 3D-print workflows.

See pricing

Related reading