To laser engrave acrylic, use cast acrylic and a CO2 laser at high speed and low power: cast sheet turns frosty white, while extruded sheet engraves almost clear. A blue diode laser passes straight through clear acrylic, so on a diode you need opaque or dark sheet, or a removable dark coating on clear sheet.
Those two choices, sheet type and wavelength, decide most acrylic jobs before you touch a setting. The numbers below are starting ranges taken from manufacturer material guides, not promises. Acrylic is also one of the more flammable things you will put in a laser, so read the safety section.
Which laser engraves which acrylic
| Acrylic | CO2 laser (10.6 µm) | Blue diode (about 450 nm) | Fiber or 1064 nm infrared |
|---|---|---|---|
| Clear cast | Frosty white engraving, clean cut | Beam passes through. Needs a dark coating to engrave, will not cut | No. xTool states its infrared module cannot engrave transparent acrylic |
| Clear extruded | Faint, near-clear engraving. Flame-polished cut edge | Beam passes through | No |
| Black or dark opaque | Engraves and cuts | Engraves and cuts thin sheet | Surface marks only (a whitened mark on black) |
| White, blue, pale translucent | Engraves and cuts | Poor. xTool lists white and blue as colours a blue diode cannot cut | Not a practical choice |
| Two-tone sheet or engraving laminate | Removes the thin cap to show the core colour | Depends on cap colour. Check the listing for your machine | Depends on the product |
Epilog and xTool give the same reason for the split: a 10.6 µm CO2 beam is absorbed by every colour of acrylic, including clear, and a blue diode beam is not. The wider machine trade-offs are in the fiber vs CO2 vs diode comparison.
Starting settings for acrylic by laser class
| Laser class | Engraving start point | Cutting 3 mm start point | Published by |
|---|---|---|---|
| 10 W diode (opaque black only) | 50% power, 3,000 mm/min, 1 pass | 100% power, about 3 mm/s (180 mm/min), 2 passes | Creality Falcon (engrave), xTool M1 (cut) |
| 20 to 22 W diode (opaque only) | 40 to 50% power, 3,000 to 4,000 mm/min | 55% power, 180 to 200 mm/min, 1 pass on black frosted sheet | Creality Falcon2 22 W |
| 40 W diode (opaque only) | 22 to 26% power, 3,000 to 4,000 mm/min | 30% power, 180 mm/min, 1 pass | Creality Falcon2 40 W |
| 30 to 60 W RF CO2 (Epilog, Trotec, Universal class) | 35 to 40% power, 70 to 80% speed, 400 DPI | Slow speed, high power, one pass. Epilog rates 30 to 40 W for 3 mm sheet | Rowmark laser reference, Epilog |
| 60 W glass-tube CO2 | 30% power, 300 DPI, at the fastest raster speed the machine holds cleanly | 60 to 65% power, 8 to 12 mm/s | Thunder Laser (engrave), OMTech (cut) |
| 80 to 100 W glass-tube CO2 | 20 to 25% power, 300 DPI | 55 to 65% power, 15 to 20 mm/s | Thunder Laser (engrave), OMTech (cut) |
| 50 W fiber (black acrylic, mark only) | 15% power, 3,500 mm/s, 100 kHz, 2 passes | Does not cut acrylic | Thunder Laser |
Treat every row as the first square of a test grid, and run a small power and speed matrix on an offcut of the same sheet before the real part (the LightBurn beginner walkthrough covers setting one up). The glass-tube cutting figures come from OMTech's acrylic guide for 3 mm cast sheet. Thunder Laser's raster figures assume 1,200 mm/s. If your gantry runs slower, drop power with it: Rowmark's laser reference gives the rule of thumb that halving the speed doubles the depth.
How to steer from the first test:
- Too faint or patchy: check focus first, then raise power in small steps or slow down slightly.
- Glossy, melted or distorted: too much energy. Raise speed or cut power. Epilog notes that excess power distorts the sheet.
- White, snow-like residue in a deep engraving: Trotec's acrylic guide recommends several lighter passes instead of one slow, high-power pass.
- Visible raster lines: a second pass slightly out of focus smooths the surface. Rowmark suggests dropping the bed about 0.5 mm (0.020 in).
Cast vs extruded acrylic: why one frosts white and the other does not
Both are PMMA. The difference is how the sheet was made.
Cast acrylic is poured as liquid and cured in a mould, which gives it a higher molecular weight. Under a light, fast pass the surface ablates into a fine rough texture that scatters light. That scatter is the white frost. Extruded acrylic is pushed through a die in a continuous process and melts more readily. The engraved area flows back smooth, so it stays nearly clear. Trotec describes the extruded result as matte grey and the cast result as bright, high-contrast white.
| Property | Cast (GS) | Extruded (XT) |
|---|---|---|
| Engraving | Frosty white, high contrast | Clear to matte grey, low contrast |
| Laser-cut edge | Clean and burr-free, not flame-polished | Glossy, flame-polished |
| Thickness tolerance (Trotec) | About ±15% | About ±5% |
Buy cast for anything where the engraving is the point: awards, edge-lit signs, photo panels. Buy extruded when the job is mostly cutting and a glossy edge matters. If you are stuck with extruded sheet, Trotec's guide offers a workaround: convert the artwork to 60 to 70% grey so it rasters as a halftone, which adds some contrast.
How do you tell cast acrylic from extruded?
Engrave a small test square in a corner: a bright, even white frost means cast, and a faint clear or grey mark means extruded. The two look identical in the hand, so check the supplier's listing first. The wide thickness tolerance of cast sheet is also a reason to measure and refocus on every new sheet.
Can a diode laser engrave clear acrylic?
Not directly. Clear acrylic is transparent to the blue light a diode laser emits (xTool quotes 450 to 455 nm for its modules), so the beam passes through without heating the sheet. Extra wattage does not change this, because the energy is never absorbed.
The workaround xTool documents is a removable dark layer that absorbs the beam and transfers heat into the surface:
- Peel the film from one face and coat it with something water-removable: tempera, watercolour, chalk or mural paint, or dry-erase marker.
- Hold the sheet up to a light. Thin patches engrave unevenly, so recoat until it is opaque.
- Raise the sheet off the bed. Whatever light gets through should not heat the base plate under the acrylic.
- Engrave fast at low to medium power, then let the sheet cool before handling.
- Wash the coating off with warm water.
The coating colour transfers permanently into the mark, dark colours work best and white works worst, and the result is a surface texture, not a deep engraving. It does not make a diode cut clear sheet. xTool also warns against paint strippers, which attack acrylic.
Can a diode laser engrave black acrylic?
Yes. Opaque black acrylic absorbs blue light well, so a 10 to 40 W diode both engraves it and cuts thin sheet. Creality's Falcon tables list 3,000 to 4,000 mm/min for engraving and roughly 120 to 200 mm/min for cutting 3 to 4.6 mm black sheet, with power falling as module wattage rises.
Colour matters more than opacity. The same tables include settings for transparent red, yellow and green sheet, colours that absorb blue. xTool lists clear, white and blue as the ones a blue diode cannot cut.
Reverse engraving for edge-lit signs
Most acrylic awards and LED signs are engraved on the back and viewed through the front. The front face stays glossy, and the frosted engraving scatters light fed in through the edge.
- Use clear cast sheet, 3 mm or thicker.
- Mirror the artwork before sending the job. Text must read backwards on screen.
- Remove the film from the back, the face being engraved, and leave the front film on until the job is finished, as Epilog recommends.
The same back-face method suits portraits. The image prep (contrast, dithering, DPI) is covered in the guide to engraving a photo with a laser. If you want the panel carved as a relief with real depth instead of a flat frost, the laser needs a grayscale depth map, not a photograph. DepthGen Pro generates one offline from a photo or logo and exports 8-bit or 16-bit PNG.
Masking: when to leave the film on
Bare acrylic engraves best. Trotec's processing guide says engraving through the protective backing takes more power and loses fine detail, and a plastic film can melt into the surface.
- Cutting: a paper mask can stay on to keep smoke off the surface. If you see flare-ups, or the parts are small and thin, take it off. Trotec lists protective backing as one cause of flames.
- Clear plastic film: remove it, or replace it with paper transfer tape.
- Residue on deep engraving: Trotec suggests a thin coat of liquid dish soap on the surface as a non-flammable barrier that rinses off afterwards.
What paint do you use to fill laser engraved acrylic?
Water-based acrylic craft paint. It is the common choice for colour-filling engraved acrylic, and it carries no solvent to attack the sheet. Trotec's guide warns that cleaners or paints containing alcohol cause micro-fractures in laser-processed areas, so avoid solvent-based paints and alcohol markers.
The usual method is to use the mask as a stencil:
- Leave the paper mask on, or apply paper transfer tape, and burnish it flat.
- Engrave through the mask. Expect to add a little power and lose some very fine detail.
- Brush or spray paint into the engraving while the mask is still in place.
- Let it dry, then peel the mask.
On a reverse-engraved sign, paint the back. The colour shows through the clear front.
Two-tone acrylic and engraving laminate
Two-tone sheet has a thin coloured cap over a contrasting core. The laser removes the cap and the core colour shows through, which gives sharp contrast for name badges, control panels and signs without paint.
Rowmark says its laserable sheets use impact-modified acrylic made for CO2 systems, and its starting point for standard two-ply sheet on a 60 W RF machine is 35% power, 70% speed and 400 DPI in one pass. From the same guide:
- Remove the printed protective mask before engraving.
- Large engraved areas build heat in the core and can warp or crack the sheet. Use lower power and DPI with more than one pass.
- Reverse-engravable grades have a clear face with the colour on the back. Mirror the artwork and engrave from the back, the same as an edge-lit sign.
Diode owners should check each colour: xTool's own listings clear some two-tone colours for its blue-diode machines and not others. Confirm the product is acrylic too. ABS-based engraving sheet made for rotary engravers does not belong in a laser, as the guide to which plastics are safe to laser explains.
Cutting acrylic is the opposite of engraving it
Engraving is fast and light. Cutting is slow and hot, because a good acrylic cut melts its way through and leaves the edge polished.
- Power: Trotec's rule of thumb is about 10 W of CO2 power per 1 mm of thickness. Epilog rates 30 to 40 W for 3 mm sheet and 50 to 60 W for 6 mm.
- One pass: Trotec advises cutting in a single pass, since repeated passes leave visible steps in the edge.
- Air assist: keep it low, 0.2 bar or less. Hard air cools the melt and leaves a milky edge.
- Lift the sheet: support it on pins or standoffs so the beam does not reflect off the bed into the underside.
- Exhaust: pull air from below the sheet so vapour leaves the kerf.
Is it safe to laser engrave acrylic?
Yes, with extraction running and someone watching the machine. Acrylic does not release chlorine or cyanide compounds the way PVC or ABS do, but it has two real hazards.
Fire. Epilog states that acrylic in all its forms has proven especially flammable when laser cut and that you should never leave the machine unattended. The vapour itself is flammable, which is why weak exhaust and slow cuts cause flare-ups. Keep a suitable extinguisher within reach.
Fumes. The beam breaks PMMA back down into methyl methacrylate. Workplace measurements by France's INRS found methyl methacrylate and formaldehyde at an acrylic laser-cutting station. A 2023 UCLA study found that ultrafine particles escaped each time the lid was opened after a cut and kept rising for at least 20 minutes. Vent outdoors or through a filter unit rated for fumes, and let the enclosure clear before you open it.
Wear eye protection matched to your laser's wavelength. On a diode, remember that the beam leaves the bottom of a clear sheet and lands on whatever is underneath.
Common failures and fixes
| Problem | Likely cause | Fix |
|---|---|---|
| Engraving is clear, not white | Extruded sheet, or cast sheet out of focus or underpowered | Switch to cast, refocus, add a little power, or use the 60 to 70% grey halftone method |
| Melted, glossy or warped engraving | Too much energy | Raise speed, lower power, split deep work into passes |
| Uneven frost or banding | Focus drifting across a sheet of uneven thickness, a dirty lens, or a patchy coating on a diode job | Measure and refocus, clean the lens, recoat until opaque |
| Flames while cutting | Poor exhaust, backing left on, focus off, or sheet too thick for the wattage | Improve airflow under the sheet, strip the backing, refocus, cut thinner stock |
| Marks on the underside or edge | Beam reflecting off the bed | Raise the sheet on pins and increase speed |
| Milky or frosted cut edge | Too much air assist | Reduce air pressure |
Why does laser cut acrylic crack after cleaning?
The laser leaves a band of stressed material along every cut and engraved edge, and alcohol or solvent makes that stress release as a web of fine cracks, called crazing. Acrylite's fabrication brief puts that zone at roughly 0.25 to 1.3 mm into the sheet and says it is very susceptible to crazing from incompatible solvents or from bending.
Clean finished parts with mild soap and water or a cleaner made for acrylic. Keep isopropyl alcohol, solvent cleaners and solvent-based paints away from laser edges. To reduce the stress at the source, Acrylite's advice is lower power with a faster feed, at the cost of a less glossy edge. Parts that will be solvent-cemented or loaded can be annealed to the sheet maker's schedule.
The practical verdict
For engraving, buy cast acrylic and run it on a CO2 laser, fast and light, on the back face if the piece will be viewed through the front or lit from the edge.
On a diode, work with opaque dark sheet or two-tone sheet cleared for your wavelength. Use the washable-coating method for the occasional clear piece and expect a lighter, rougher mark.
For cutting, extruded sheet gives the glossy edge. Go slow, in one pass, with low air and strong exhaust, and stay with the machine. Keep alcohol off every laser-cut edge.
Sources
- Epilog Laser: Laser Cutting Acrylic
- Trotec: Laser processing on acrylic
- Trotec: Laser Processing Guide, working with acrylic (PDF)
- xTool Support Center: Acrylic Engraving Tutorial
- Thunder Laser: Laser settings for cutting, engraving and marking
- Creality Falcon: Material Settings of Creality Falcon Laser Series
- Rowmark: Laser Reference Guide (PDF)
- ACRYLITE: Laser Machining fabrication brief
